月份: enero 2022
Cómo calcular el peso de una varilla de PEEK
La fórmula de cálculo del peso de la varilla de PEEK es: masa = volumen x densidad. La densidad del PEEK puro es aproximadamente 1,3 y la del PEEK modificado es aproximadamente 1,4. Sin embargo, cabe señalar que el diámetro exterior de la varilla de PEEK es generalmente mayor. la calibración, por lo que el peso de una sola varilla debe basarse en el diámetro exterior real.
2022-01-20 | Preguntas frecuentes | Etiquetas: Perfiles de PEEK, Varillas de PEEK
Se lanza oficialmente AKSOPEEK, una nueva generación de materiales médicos implantables
At present, my country’s implant-grade PEEK materials mainly rely on imports. Based on market feedback and national R&D project needs, Junhua PEEK launched the domestic implant-grade PEEK material brand AKSOPEEK series products. At the same time, in response to the needs of national intellectual property protection, the company’s products further strengthened management when they enter the market to enhance product awareness. The company applied to the State Administration for Industry and Commerce for the AKSOPEEK trademark, and was approved for registration and issued a certificate by the Trademark Office of the State Administration for Industry and Commerce in December 2021. AKSOPEEKBrand Value 01. AKSO is full of value and profound meaning. In ancient Greek mythology, it is the representative…
2022-01-15 | Noticias, Noticias de la empresa | Etiquetas: Noticias de la empresa
Molde de precisión para inyección de PEEK para medicina deportiva
Since the 1970s, joint surgery has made great progress in the United States and other countries. In the past few decades, arthroscopy has had a revolutionary impact on the diagnosis and treatment of intra-articular diseases. However, the first generation of shoulder arthroscopy equipment uses stainless steel and titanium anchors, both of which will fail due to the breakage of the sutures in the metal eyelets. For this reason, the medical device industry has made many attempts and designed a variety of injection molded products – implant-grade PEEK anchors. PEEK is strong and tough, and can provide strength similar to that of metal. If a revision surgery is required, it can be drilled through without increasing the difficulty of the surgery….
2022-01-11 | Noticias, Noticias de la empresa | Etiquetas: Noticias de la empresa
Las pruebas PEEK de Junhua cumplen con la TSCA
PRRT 01. Definition and History of TSCA TSCA stands for Toxic Substances Control Act, or TSCA for short. It was enacted by the U.S. Congress in 1976 and took effect in 1977. The U.S. Environmental Protection Agency (EPA) is responsible for its implementation. The Act aims to comprehensively consider the environmental, economic and social impacts of chemical substances circulating in the United States and prevent «unreasonable risks» to human health and the environment. After several revisions, TSCA has become an important regulation for the effective management of chemical substances in the United States. For companies whose products exported to the US market fall into the TSCA regulatory category, TSCA compliance is a prerequisite for normal trade in US products. These…
2022-01-07 | Noticias, Noticias de la empresa | Etiquetas: Noticias de la empresa
Junhua PEEK participó en la formulación de estándares nacionales para resina de polieteretercetona (PEEK)
National Standard for Polyetheretherketone (PEEK) Resin The National Standardization Administration issued Document No. 40 [2019] «Notice of the National Standardization Administration on Issuing the Fourth Batch of Recommended National Standard Plans in 2019», which issued the national standard formulation plan for «Polyetheretherketone (PEEK) Resin», with project number 20194348-T-606. The standard plan project was proposed by the China Petroleum and Chemical Industry Federation, under the jurisdiction of the Plastics Standardization Technical Committee, and implemented by the Engineering Plastics Sub-Technical Committee of the Plastics Standardization Technical Committee. Junhua PEEK participated in the online video discussion on the draft national standard for polyetheretherketone (PEEK) resin and the 2021 Annual Meeting and Standard Review Meeting of the Engineering Plastics Branch of the Plastics Standardization…
2022-01-04 | Noticias, Noticias de la empresa | Etiquetas: Noticias de la empresa